LEE PRECISION

Lee Precision, the nation's number one manufacturer of reloading equipment for over 50 years presents its full inventory of quality products. If you are thinking about starting to reload, you found the best place to start. Reloading indeed saves you money, and no manufacturer saves you more than Lee.

View as Grid List

Sort by

Display per page

LEE DELUXE POWER QUICK TRIM

R650,00

Ultimate in Case Trimming Speed and Convenience, trim, chamfer and deburr the inside and outside of case necks in a matter of seconds. Hex shank snaps into a cordless screwdriver or drill (sold separately). Includes power Quick Trim adapter, chip catcher, and deluxe cutter assembly. To complete your trimming setup, order cartridge specific pistol Quick Trim die or rifle Quick Trim die.

LEE PRECISION MOLD DC 401-175-TC

R595,00

Lee Double Cavity Mold produces a .401 diameter 175 grain truncated cone nose bullet suitable for cartridges like 40S&W, 10MM. Handles included.

LEE PRECISION CASE FEEDER TUBES (7)

R305,00

Lee Case Feed Tubes includes seven replacement Case Feeder Tubes for the Pro 1000 and LoadMaster.

LEE PRIMER ATTACHMENT

R295,00

Lee Primer Attachment used for conversion to a different primer size for the Pro 1000 Press. Includes large and small troughs, primer pins, spring, and a folding primer tray.

LEE UNIVERSAL DECAPPING DIE

R370,00

An absolute must for those who clean cases before reloading. Cases need not be clean nor lubed when using this die. Cases are not sized at all, only deprimed. Works on boxer-primed brass only. Fits cases up to .560" in diameter and up to 3.125" long.

LEE UNIVERSAL DECAPPING PIN

R100,00

Lee Replacement decapping pin for our Universal Decapping Die (#90292)

LEE PRIMER PIN SPRING

R20,00

Part LM3290 for product LOAD MASTER LG PRIMER FEED (Code=90077)

LEE CARBIDE FACTORY CRIMP DIE 44SP/MAG/RUSSIAN

R640,00

Lee 44 Special, 44 Magnum, and 44 Russian Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory-like dependability. This die applies a roll crimp. The adjusting screw quickly and easily sets the desired amount of crimp. Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow-burning magnum powders.

LEE PRO AUTO DISK UPDATE KIT

R610,00

Lee Pro Auto Disk Update Kit updates any Auto Disk Powder Measure with Pro features, except the non-stick coating. Includes oversize hopper and valve assembly, pull back lever, chain and attachments, solid brass knurled thumbed nuts, and Swivel Adapter. Update Kit also includes a FREE Adjustable Charge Bar.

LEE CRANK SLIDER (ASSY)

R40,00

Part LM3258 for product LOAD-MASTER 45 COLT (Code=90946)

LEE 338 LAPUA COLLET DIE SET

R2 515,00

Lee Large Series (1 1/4x12 thread) Collet Neck Sizing 2-Die Set for 338 Lapua, used with the Classic Cast Press only. Includes collet neck sizing die, bullet seating die, load data, and instructions. Reloading press #25 shell holder sold separately. Powder Dipper not included.

LEE SMALL LM PRIMER TROUGH ASSEMBLY-BLK

R290,00

There was a third-generation design change on the primer feeder effective October 27, 2011, eliminating nuisance damage to the primer sliders and trough cover during operation. Formerly the gray cover and trough, now sold as an assembly along with the primer slider, primer lever, 6-32 x 1/4 screw, and o-ring. These parts are no longer available individually. This assembly replaces parts: LM3254, LM3253A, LM3253B, and LM3251

LEE INDEXER & FLIPPER COMBO

R275,00

Part LM3243 Indexer with LM3244 Flipper for products: LOAD-MASTER 32 S&W LONG and 32 H&R MAG (Code=90935), LOAD-MASTER 380 AUTO (Code=90937), LOAD-MASTER 38 SPECIAL AND 357 MAG (Code=90938), LOAD-MASTER 40 S&W (Code=90940), LOAD-MASTER 9mm LUGER (Code=90936), LOAD-MASTER 45 ACP (Code=90945) and LOAD-MASTER 45 COLT (Code=90946)

LEE DECAPPER PIN 6.5X55

R75,00

Part SE2425 for product RGB DIE 6.5X55 (Code=90874) and 6.5 Carcano PaceSetter Die Set (Code= 90749)

LEE GAUGE/HOLDER 9MM LUGER

R170,00

Lee 9MM LUGER Case Length Gauge is a precise, easy way to trim to length and square the case mouth. Used with the Cutter and Lock Stud or Zip Trim. Trim to length .744 to .754 inches.

LEE GAUGE/HOLDER 44 MAG

R145,00

Lee 44 MAG Case Length Gauge is a precise, easy way to trim to length and square the case mouth. Used with the Cutter and Lock Stud or Zip Trim. Trim to length 1.265 to 1.285 inches.

LEE LG LM PRIMER TROUGH ASSEMBLY RED

R270,00

There was a third-generation design change on the primer feeder effective October 27, 2011, eliminating nuisance damage to the primer sliders and trough cover during operation. Formerly the white cover and trough, now sold as an assembly along with the primer slider, primer lever, 6-32 x 1/4 screw, and o-ring. This assembly replaces parts: LM3252, LM3247A, LM3247B, and LM3251.