Part AO5306 pendent only for product PRO AUTO DISK (Code=90429).

SIX PACK PRO SHELL PLATE 1s works with cartridges: 38 SPECIAL, 357 MAGNUM, etc.

5 case feed tubes automate the case feeding operation on the APP, Deluxe APP, Pro 1000, Pro 4000 Kit | Auto Breech Lock Pro, Load-Master, and Six Pack Pro presses. Increases rates and has been optimized for bottleneck cartridges.

Replacement Tap for Balistix Pro Stuck Case Remover

Molded parts set for the Auto-Drum Powder Measure:

SIX PACK PRO SHELL PLATE 4s works with the following cartridges: 22 Nosler, 222, 223, 380 ACP and 300 AAC Blackout.

Lee ultimate spline drive lock rings. 3 pack of aluminum lock-rings with o-rings. One wouldn’t think you could improve on a simple thing like a lock ring, but we have. The new split clamp spline drive makes all other lock rings obsolete and clumsy to use. We started with a custom extrusion of high-strength aluminum with a splined exterior surface. We split the ring and added a cross bolt that when even lightly tightened, applies a vice-like grip on your dies. No tiny set screws that easily strip or damage your die threads. Then we added the famous Lee “O” ring because no matter how securely you have the lock ring clamped to the die, it will loosen in the press during operation without the friction of the “O” ring. The “O” ring allows you to finger tighten into your press and it will never loosen during operation yet you can easily remove your die with finger pressure. We have also included a handy slim profile lock ring wrench, that works great when fitting dies on a turret or tool head. Dies are simply easier to install with the lock ring wrench.

Hornady Adapter

Drive Bolt for Six six-pack pro reloading presses.

Part NS2624 for product COLLET 2 DI 6.5X55 (Code=90712), 6.5 CREEDMOOR ULTIMATE RIFLE DIE SET (Code=90939), and 6.5 GRENDEL COLLET DIES (Code=91606).

SMALL FEMALE CUTTER FOR QUICK TRIM

This small circular Carbide Cutter has been silver soldered and precision ground three times to provide a sharp, clean cut. When replacing the Cutter on the Outside Neck Turner, be sure to install the lead shot provided to protect the threads from the cross-locking screw that holds it in place.

Small spring steel follower that slips between the Case Trimmer Bearing and the Case Trimmer Base of the Outside Neck Turner.

Lee Breech Lock Ram Prime, Start priming in seconds, nothing to adjust.

Lee 357 MAG Case Length Gauge is a precise, easy way to trim to length and square the case mouth. Used with the Cutter and Lock Stud or Zip Trim.

Part SD2151 decapper clamp for Lee sizing dies.

The micrometer adjust screw by Lee Precision replaces the original adjusting screw on any Lee bullet seating die. Infinitely adjustable, allows precision bullet seating depth. Easy to read laser engraved divisions represent .001" one thousandth of an inch. The integrated friction ring eliminates annoying clicks that prevent splitting thousandths. No clicks, just smooth adjustment. Reads just like a precision depth micrometer, record your setting and easily return to them for future use. The micrometer adjuster can be easily transferred to other Lee Bullet Seating Dies, but it is so economically priced, you will want one for every die.

The micrometer adjust screw by Lee Precision replaces the original adjusting screw on any Lee bullet seating die. Infinitely adjustable, allows precision bullet seating depth. Easy to read laser engraved divisions represent .001" one thousandth of an inch. The integrated friction ring eliminates annoying clicks that prevent splitting thousandths. No clicks, just smooth adjustment. Reads just like a precision depth micrometer, record your setting and easily return to them for future use. The micrometer adjuster can be easily transferred to other Lee Bullet Seating Dies, but it is so economically priced, you will want one for every die.

Driver clutch for 2023 Pro 1000, Auto Breech Lock Pro, Pro 4000 Kit.

The micrometer adjust screw by Lee Precision replaces the original adjusting screw on any Lee bullet seating die. Infinitely adjustable, allows precision bullet seating depth. Easy to read laser engraved divisions represent .001" one thousandth of an inch. The integrated friction ring eliminates annoying clicks that prevent splitting thousandths. No clicks, just smooth adjustment. Reads just like a precision depth micrometer, record your setting and easily return to them for future use. The micrometer adjuster can be easily transferred to other Lee Bullet Seating Dies, but it is so economically priced, you will want one for every die.