Part NS2621 for product DLUX RIFLE 3 DI 220 SWFT (Code=90609)

Part LM3246 for product LOAD-MASTER 45 COLT (Code=90946)

Part FT1994 for product PRO CASE FEEDER RIFLE (Code=90663)

Features low profile steel base with positive through ram primer disposal. Proven design with compound leverage. No spring in this turret design. The turret is locked into a solid steel ring with big rifle bolt-type lugs. The patented design puts the lugs on the circumference so there can be no tipping. The linkage is so powerful that the largest magnum cases are sized with ease. The effort required is so small that the usual heavy bench is not essential. The Lee Turret Press has a built-in primer catcher, longer stroke, more hand clearance, and a comfortable wood grip. Even if you do not need all of these features, why pay more for anything less? In fact, you will want a Lee Turret Press even if you already own a more expensive one. The fourth hole in the turret allows you to install your Lee Factory Crimp Die or Taper Crimp Die in the press.

Part NS2622 for product COLLET DIE ONLY 243 (Code=90956)

Lee #19L shell plate for the Load-Master Press. For the 10mm Auto, 41 A&E, and similar cases.

6.5 Creedmoor PaceSetter-Die Set. The set features a full-length-resizing die to return brass to the factory's new dimensions, perfect for reloading brass fired in other guns. The Easy Adjust Dead Length Bullet seating die foolproofs the bullet seating adjustment, and assures excellent seating depth every time. The Factory Crimp die provides a secure crimp on bullets with or without a crimp groove. In most cases, it helps accuracy by providing a uniform higher start pressure and gives the finished cartridge Factory accuracy and dependability. The set is complete, with shell holder, powder measure, and famous Lee load data featuring all common brands of powder organized in an easy-to-read logical format.

Automatic Ignition Butane Powered Pro-Torch.

Part FL3336 for product LOAD-MASTER 45 COLT (Code=90946)

Part NS2623 for product COLLET DIE ONLY 25/06 (Code=90957)

Replace broken or worn decapping pins with these factory components from Lyman. Each pin is carefully crafted from high quality steel to ensure correct fit and flawless function. These pins will work to replace any age Lyman decapping pin.

Pro Stuck Case Remover by Balistix

Lee 44 Special, 44 Magnum, and 44 Russian Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory-like dependability. This die applies a roll crimp. The adjusting screw quickly and easily sets the desired amount of crimp. Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow-burning magnum powders.

Part NS2624 for product COLLET 2 DI 6.5X55 (Code=90712) and 6.5 CREEDMOOR ULTIMATE RIFLE DIE SET (Code=90939).

Pro 1000 and Value Turret Press roller handle upgrade kit. This handle can not be used on the Classic Turret Press.

Lee 6 cavity block produces a .358 diameter 158 grain Semi-Wad Cutter bullet suitable for cartridges like 38 Special, 38 S&W, 38 Colt New Police, 357 Mag. Bullet Mold lube and handles are sold separately.

Lee 300 PRC PaceSetter 3-Die Set includes a full-length sizing die, Easy Adjust Dead Length Bullet Seating Die, Factory Crimp Die, universal shell holder, powder dipper, and instructions with load data. Select this die set if you are reloading mixed-range brass.

Lee Six Cavity Mold produces a gas-checked .225 diameter 55 grain round with flat bullet suitable for .22 cal cartridges.

Part NS2625 for product COLLET DIE ONLY 270 WIN (Code=90958)

NEW PRIMER ARM for product code = 90928