Cookies help us deliver our services. By using our services, you agree to our use of cookies.
LEE PRECISION
Lee Precision, the nation's number one manufacturer of reloading equipment for over 50 years presents its full inventory of quality products. If you are thinking about starting to reload, you found the best place to start. Reloading indeed saves you money, and no manufacturer saves you more than Lee.
LEE LM SHELL PLATE #1s
R680,00
Lee #1s quick-change shell plate for the Load-Master Press. For the 38 Special, 357 Mag and similar cases.
LEE COLLET DIE ONLY 30/06
R680,00
Lee 30/06 Collet Die only that uses a Collet to squeeze a Mandrel, creating a precisely aligned case neck while reducing run out. Sizes just the neck and requires no lubrication.
LEE HAND PRIMING TOOL SHELL HOLDERS SET
R680,00
Lee set of Hand Priming tool shell holders, include 11 of the most popular for more than 115 different cartridges.
LEE COLLET DIE ONLY 25/06
R680,00
Lee 25/06 Collet Die only that uses a Collet to squeeze a Mandrel, creating a precisely aligned case neck while reducing run out. Sizes just the neck and requires no lubrication.
LEE COLLET DIE ONLY 223
R680,00
Lee 223 Collet Die only that uses a Collet to squeeze a Mandrel, creating a precisely aligned case neck while reducing run out. Sizes just the neck and requires no lubrication.
LEE COLLET DIE ONLY 243
R680,00
Lee 243 Winchester Collet Die only uses a Collet to squeeze a Mandrel, creating a precisely aligned case neck while reducing run out. Sizes just the neck and requires no lubrication.
Lee Safety Primer Feed Small and Large
R680,00
Lee Safety Prime is a new priming system for small and large primers, never touch the primers from box to shell. Used with 2006 and newer Breech Lock Challenger, Turret Presses, Classic Turret Press, Breech Lock Classic Cast, Classic Cast Press, and Auto Breech Lock Pro Press.
LEE CARBIDE DIE ONLY 38SP 357
R680,00
Lee 38SP 357 Carbide Full Length Sizing Die only. No case lube needed
LEE CHARGING DIE KIT
R676,00
Lee Short and Long Charging Dies are included in this kit for use with the Auto-Disk, Pro Auto-Disk, and Auto-Drum Powder Measure. Works with cases .860 to 2.620 inches long, and bullet diameters .223 and larger.
It works like the pistol Powder Through Expanding Die, except it does not expand the case mouth. Rifle case expansion is done in the Sizing die.
Lee Large Inline Bullet Feed Magazine
R675,00
Large Inline Bullet Feed Magazine works with bullet diameters of .390 to .463. 40 CAL 45 CAL
Lee Medium Inline Bullet Feed Magazine
R675,00
Medium Inline Bullet Feed Magazine works with bullet diameters of .300 to .372. 30 CAL 35 CAL
LEE LM SHELL PLATE #19s
R670,00
Lee #19s shell plate for the Load-Master Press. For the 9mm Luger, 40 S&W, 38 Super and similar cases.
LEE COLLET DIE ONLY 300 WM
R660,00
Lee 300 Win Mag Collet Die only that uses a Collet to squeeze a Mandrel, creating a precisely aligned case neck while reducing run out. Sizes just the neck and requires no lubrication.
LEE COLLET DIE ONLY 308 WIN
R660,00
Lee 308 Win Collet Die only that uses a Collet to squeeze a Mandrel, creating a precisely aligned case neck while reducing run out. Sizes just the neck and requires no lubrication.
LEE COLLET DIE ONLY 260 REMINGTON
R660,00
Lee 260 Remington Collet Die only uses a collet to squeeze a mandrel, creating a precisely aligned case neck while reducing run out. Sizes just the neck and requires no lubrication.
LEE APP BULGE BUSTER KIT
R660,00
The Lee App Bulge Buster Kit and the appropriate Lee Carbide Factory Crimp Die restores the free function of rimless cases that have low base bulges. Low base bulges usually occur from chambers that do not fully support the cartridge or cases resized in carbide dies from manufacturers other than Lee. These show a noticeable stop ring near the base. You will most likely find cases with these problems in mixed range brass.
LEE DELUXE POWER QUICK TRIM
R650,00
Ultimate in Case Trimming Speed and Convenience, trim, chamfer and deburr the inside and outside of case necks in a matter of seconds. Hex shank snaps into a cordless screwdriver or drill (sold separately).
Includes power Quick Trim adapter, chip catcher, and deluxe cutter assembly. To complete your trimming setup, order cartridge specific pistol Quick Trim die or rifle Quick Trim die.
LEE CARBIDE FACTORY CRIMP DIE 45ACP
R650,00
Lee 45 ACP, 45 AUTO RIM, 45 WIN MAG, and 45 GAP Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory-like dependability. This die applies a taper crimp. The adjusting screw quickly and easily sets the desired amount of crimp. Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow burning magnum powders.
SPLINE DRIVE BREECH LOCK BUSHING 4-PACK
R645,00
Spline drive Breech Lock Bushings 4 pack. A new, easy-grip splined drive surface allows easy, accurate, and fast die installation in your press. Reloading dies are confusingly similar looking, so we anodized and colored the bushings so you can “color code” your dies for quick positive identification. No need for lock rings on your dies with these quick-change bushings. Simply lightly tighten the hex clamp screw, and the split collar will put a vise lock on your die. Loosen the screw, and the die will spin freely. Once set you’ll never lose position.
Lee 380 Auto Carbide Factory Crimp Die
R645,00
Lee 380 Auto Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory like dependability. This die applies a taper crimp.