Cookies help us deliver our services. By using our services, you agree to our use of cookies.
LEE PRECISION
Lee Precision, the nation's number one manufacturer of reloading equipment for over 50 years presents its full inventory of quality products. If you are thinking about starting to reload, you found the best place to start. Reloading indeed saves you money, and no manufacturer saves you more than Lee.
Lee Load Master LG Primer Feed
R550,00
Lee Load-Master Large Primer Feeder for quick change to the large primer size for the Load-Master Press.
LEE CARBIDE DIE ONLY 45 ACP
R540,00
Lee 45 ACP Carbide Full-Length Sizing Die only. It also fits the following calibers: 45 Auto Rim, 45 GAP and 45 Win Mag. No case lube required.
LEE AUTO BREECH LOCK PRO SHELL PLATE #19
R540,00
Breech Lock Pro Shell Plate # 19, works with cartridge: 40 S&W, 10mm Auto, 9mm Luger, 38 Super, 38 Auto, 41 AE.
LEE CARBIDE FACTORY CRIMP DIE 40SW 10MM
R520,00
Lee 40 S&W/10mm Auto Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory-like dependability. This die applies a taper crimp. The adjusting screw quickly and easily sets the desired amount of crimp. Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow burning magnum powders.
LEE BREECH LOCK PRO SHELL PLATE 1
R520,00
Breech Lock Pro Shell Plate # 1
Works with cartridges: 38 Special, 357 Magnum, etc.
LEE BREECH LOCK RAM PRIME
R520,00
Lee Breech Lock Ram Prime, Start priming in seconds, nothing to adjust.
LEE 6.5 CREEDMOOR FULL LENGTH SIZING DIE
R520,00
6.5 Creedmoor Rifle Steel Full Length Sizing Die Complete.
LEE BREECH LOCK PRO SHELL PLATE 2
R505,00
Breech Lock Pro Shell Plate # 2
Works with cartridges: 45 ACP, 45 GAP, etc.
Lee Multi Tube Feeder
R500,00
Lee Multi-Tube Feeder features a four tube magazine that holds up to 100 bullets and keeps the Bullet Feeder fed with a continuous supply of bullets.
LEE BULLET SEAT DIE 9MM LUGER
R499,00
9mm Luger pistol bullet seating die only complete. There are two crimp shoulders in our pistol Bullet Seating Dies. The first shoulder applies a slight taper crimp and the second shoulder applies a full roll crimp. The closer the die is adjusted to the shell holder the heavier the crimp will be.
Lee Precision Spline Drive Breech Lock Bushings (3 Pack)
R499,00
Spline drive Breech Lock Bushings 3 pack. The new, easy-grip splined drive surface allows easy, accurate, and fast-die installation in your press. Reloading dies look similar, so we anodized and colored the bushings so you can “color code” your dies for quick identification. No need for lock rings on your dies with these quick-change bushings. Simply lightly tighten the clamp screw, and a split collar will put a vice lock on your die. Loosen the screw, and the die will spin freely. Once set you’ll never lose position.
LEE PRO SHELL PLATE #1
R495,00
Lee Pro Shell Plate #1 for quick caliber change for the Pro 1000 Press. For the 38 Special, 357 Mag and similar cases.
LEE BULGE BUSTER KIT
R480,00
Lee Bulge Buster Kit and the appropriate Lee Factory Crimp Die assures your mixed brass is bulge free. This push through die adapter will quickly remove the annoying bulge rings that shell holder constrained dies simply can't reach.
Lee Deluxe Cutter Assembly
R480,00
Deluxe Cutter Assembly for use with Quick Trim Case Trimmer
Update your Value Trim adding automatic case chamfering or use to replace a dulled cutter.
LEE CHARGING DIE KIT
R480,00
Lee Short and Long Charging Dies are included in this kit for use with the Auto-Disk, Pro Auto-Disk, and Auto-Drum Powder Measure. Works with cases .860 to 2.620 inches long, and bullet diameters .223 and larger.
It works like the pistol Powder Through Expanding Die, except it does not expand the case mouth. Rifle case expansion is done in the Sizing die.
LEE FACTORY CRIMP DIE 5.7x28 FN
R470,00
Lee 5.7X28 FN Bottle Neck Factory Crimp Dies crimps the bullet firmly in place for the bottleneck cartridge
LEE PRO SHELL PLATE #2
R470,00
Lee Pro Shell Plate #2 for quick caliber change for the Pro 1000 Press. For the 45 ACP, 45 GAP, 400 Cor-bon and similar cases.
LEE PRO SHELL PLATE #19
R467,00
Lee Pro Shell Plate #19 for quick caliber change for the Pro 1000 Press. It is used for 40 S&W, 10mm AUTO, 9mm Luger, 38 Super, 38 AUTO, 41 AE and similar cases.
LEE QUICK CHANGE DRUM SET
R450,00
Features four precision molded nylon drums:
(2) small drums for charging 25 ACP to 223 Remington
(2) large drums for charging the 223 Remington to Large Magnums. Also, include an insert to allow reduced capacity charging similar to a smaller drum.
Quickly set your charge, and mark it and the powder type on the flat of the drum set for easy reference for future reloading.
LEE 3 HOLE TURRET
R450,00
Lee Aluminum 3-Hole Turret for quick change turret for the 3-Hole Turret Press and Pro 1000. This 3 hole turret will not work in our 4 Hole Turret Press or 4 Hole Classic Turret Press.